Klip-BILT II®

Product Specs

Klip-BILT II Specifications

Klip-BILT II® shelving is constructed using industrial grade steel to create adjustable, structurally independent units. Each Klip-BILT II is composed of posts, back and side cross bracing or panels, shelves, and auxiliary hardware. A variety of accessories can be added to the basic unit depending on your particular storage requirements.

Stock nominal unit sizes are 36 or 48" wide by 12, 18, or 24" deep. Available heights include: 3'4", 6'-1", 7'-1", 8'-1", and 10'-1". Other sizes are available upon request.

Component Parts

OFFSET ANGLE POST - to be 13 Ga. steel formed into an angle. Each post to have 1" front face flange and a 2-1/16" side flange, the latter having a channel shaped offset for added strength. Both flanges to be punched with 5/16" dia. holes on 1-1/2" centers for attaching sway braces, panels, and certain accessories. The 2-1/16" flanges to be punched with 1/2" by 7/16" rectangular slots on 1-1/2" centers to accommodate shelf clips.

STRONG BOX POST - to be 13 Ga. steel formed into a tubular shape 3/4" by 2-1/16". The 2-1/16" flanges to be offset at the back of both sides to form a closed tubular shape. The 3/4" front face flange to be free of punching. The 2-1/16" flanges to be punched with 5/16" dia. holes on centers for attaching sway braces, side panels, and certain accessories. The 2-1/16" side flanges to also be punched with 1/2" by 7/16" rectangular slots on 1-1/2" centers to accommodate shelf clips.

TYPE A SHELF - to be 20 Ga. steel with all four sides flanged 1-1/8" at 90 degrees. Front and back to have 9/16" return flanges at 115 degrees. Both sides to have 5/8" return flanges at 90 degrees. Shelf corners to be closed, overlapped, and welded. Front and back flanges to be punched for attaching reinforcing bars, back panels, and certain accessories. Side flanges to be punched at the corners for use when shelves are bolted to the posts. Top surface of shelf to be punched with two rows of 5/16" dia. holes for attaching shelf dividers.

SHELF CLIP - to be one-piece 13 Ga. steel reinforced with flanges around the edges. Clips to be formed with two integral tabs that allow for fastening into post slots. Clips to be independent of those in adjoining units to provide fully independent shelf adjustability.

SIDE/BACK CROSS BRACE: FLAT END - to be 12 Ga. steel 3/4" wide. Braces to be punched at each end for bolting to posts and at the center for bolting together in pairs.

BACK CROSS BRACE: UNIVERSAL - to be 12 Ga. steel 3/4" wide and flanged at each end. Braces to be punched at each end for bolting to posts and at the center for bolting together in pairs.

SIDE PANEL - to be 24 Ga. flat steel sheets punched with 5/16" dia. holes on 1-1/2" centers. Punches to be on both edges for bolting to posts.

BACK PANEL - to be 24 Ga. flat steel sheets punched with 5/16" dia. holes on 1-1/2" centers. Punches to be on both edges for bolting to posts and at the center for attaching to shelves.

UNIVERSAL FOOT PLATE - to be 11 Ga. steel 2-7/8" by 4-1/16" punched with two holes for 1/2" dia. floor anchors. Foot plate to be formed with an integral tab for attaching to posts.

Accessories

SHELF DIVIDER - to be 22 Ga. steel. Top and bottom to be flanged 5/8" at 90 degrees and punched for attaching to shelves. Front and back edge to have a 5/16" dia. bead.

SLIDING DIVIDER - to be 20 Ga. steel. Front face to be 3" by 1-1/4" with a 3/8" return flange. Base to be 3" wide by the depth of the shelf with a 1/2" flange at the back. Vertical edge to ascend, then round into a 30 degree slope towards the top.

BASE FRONT - to be 20 Ga. steel with a 2-7/8" high face. Bottom to be flanged 7/16" with a return flange of 11/32" at 90 degrees. Top flange to be formed at an angle to rest under the flange of the shelf. Ends to have tabs that secure the base front in place.

BIN FRONT - to be 18 Ga. steel with a 3" high face. Front to have 1/2" flange with 15/32" return flange at 90 degrees on top. Sides to be flanged and punched for bolting to posts.

LABEL HOLDER - to be transparent, 7/8" high plastic formed into a "C" shape for facilitating the insertion and retention of labels. Both ends and the center to be punched, ensuring swift attachment to the face flange of shelves.

Mezzanine Components

Other

FINISH - All non-hardware parts are powder-coated. Bolts, nuts, and other hardware items (e.g. shelf clips, foot plates) are zinc plated.

CLICK HERE or below for the Klip-BILT II product specifications.

Product Specifications for Klip-BILT II